Mold colonies in crawl spaces originate at ground level and migrate upward through your home's air supply. JCB Waterproofing and Construction installs certified encapsulation systems that cut off moisture at the source.
What makes our encapsulation installs last decades, not years.
Our material specs match what commercial builders require, not the minimum code standard for residential construction.
We seal every penetration -- pipes, posts, and support columns -- individually so the barrier is continuous with no gaps that allow moisture to bypass the system.
Sealed crawl spaces consistently show measurable reduction in heating and cooling costs because conditioned air is no longer exchanged with the unconditioned crawl space below.
Wood floor joists exposed to sustained humidity above 20 percent begin to lose structural integrity within a few years -- encapsulation stops that deterioration before it becomes expensive.
The science behind crawl space encapsulation centers on moisture vapor transmission from exposed soil surfaces. Even dry-looking crawl space soil emits moisture vapor continuously at a rate that can introduce gallons of water per day into the air under your home. Traditional building practice placed foundation vents to exhaust this moisture, but research has repeatedly shown that venting in humid climates introduces more moisture than it removes, because the air flowing in from outside is often more humid than the air inside the crawl space. Sealing the crawl space and managing its humidity with a rated dehumidifier consistently outperforms venting in NY climates.
Seam treatment is what separates a professionally installed system from a DIY job that looks similar from a distance. Every seam in our installations is lapped a minimum of 12 inches and taped with a 4-inch crawl space tape rated for the temperature and humidity cycle of your crawl space. Penetrations for plumbing pipes, support columns, and structural posts are individually wrapped with additional barrier material and taped circumferentially so the junction between the pipe and the barrier is fully sealed. A barrier with unsealed seams can still allow significant moisture vapor migration because vapor follows the path of least resistance -- which is any gap, however small.
Wood rot in crawl space framing begins when wood moisture content exceeds approximately 19 to 20 percent and stays elevated long enough for decay fungi to establish. Decay fungi are present in virtually all soil and all crawl space environments -- the limiting factor is not their presence but the moisture level that allows them to become active. Floor joists exposed to a wet crawl space can develop visible decay within a few wet seasons, and the damage is progressive: soft spots in floors, squeaking from weakened joists, and in severe cases structural deflection in floor systems become evident. Our assessments photograph and document all floor joist and beam conditions so you understand the current state of your structure before and after encapsulation.
Mold remediation is frequently required in conjunction with encapsulation when visible mold colonies are already established on floor joists, subfloor sheathing, or HVAC components in the crawl space. We assess mold extent as part of every inspection and provide a remediation plan that addresses existing growth before the encapsulation barrier is installed. Installing a vapor barrier over active mold does not eliminate it -- the mold must be treated first to prevent it from continuing to develop and produce airborne spores that migrate into the living space. Our remediation process uses EPA-registered fungicidal treatments applied to all affected wood surfaces, followed by a borate-based preservative application to inhibit future growth.
Six crawl space services that address every moisture source under your Interlaken home.
20-mil reinforced poly barrier installed across the entire crawl space floor and up foundation walls, sealed at all seams and penetrations for complete moisture control.
Dehumidifier placement and airflow direction are planned to ensure even coverage of the entire sealed space, with no humidity pockets that allow localized moisture buildup.
Existing foundation vents are sealed with rigid foam insulation cut to size and adhered with spray foam to eliminate the primary pathway for outside humid air to enter the crawl space.
Post-treatment borate preservative application inhibits future mold and decay fungi development on all treated wood surfaces under conditions of elevated humidity.
Drainage channels are integrated under the vapor barrier perimeter, routing water to a sump pit with a submersible pump sized for your drainage area.
We install weatherstripping and rigid foam panel inserts on all access points sized to provide an airtight fit that maintains the pressure balance of the sealed crawl space.
We enter the crawl space and conduct a systematic inspection of all floor and wall surfaces, document moisture meter readings at multiple locations, photograph all floor joist and beam conditions, and identify every source of water or moisture entry before recommending any course of action.
Where mold remediation is needed, we complete EPA-registered fungicidal treatment and borate application before any encapsulation materials are installed, ensuring no active mold is sealed under the barrier.
Foundation vents are sealed with rigid foam insulation and spray foam adhesive, and the crawl space access hatch is fitted with an insulating door seal panel.
We take final moisture readings and photograph the completed installation before issuing your written warranty documentation and maintenance schedule.
We noticed musty smells from the first floor for years and assumed it was just an old house. After JCB Waterproofing and Construction encapsulated our crawl space, the smell was gone within two weeks and our summer electric bills dropped noticeably. Should have done this years ago.
JCB Waterproofing and Construction did a full encapsulation in one day and left the crawl space cleaner than it was when they arrived. The dehumidifier they installed has not required any maintenance beyond emptying the drip tray.
I got four quotes and JCB Waterproofing and Construction was the only company that gave me a written spec listing the mil thickness of the poly they were installing. That transparency is why I chose them and their work backed it up completely.
Get a written quote from our Interlaken, NY encapsulation specialists -- no obligation, no pressure, just a clear plan.
Call +1-866-476-1348 Now